- Products
- Projects
- FeaturedRecent
1,960 more pallet positions, same four wallsSep 11, 2026
- Resources
- Blogs
- Why All Storage
- Contact
- Products
- Projects
- FeaturedRecent
1,960 more pallet positions, same four wallsSep 11, 2026
- Resources
- Blogs
- Why All Storage
- Contact
AS 4084 explained: what a racking inspection actually covers
In short:
- AS 4084.2:2023 is the Australian Standard for operating and maintaining steel storage racking, and WorkSafe Victoria points employers to it.
- Your team should check racking informally on a regular schedule, and a competent person should inspect it formally every 12 months.
- Inspectors check loads, beams, uprights, plumb, bracing, floor fixings and protection.
- Damage is rated red, amber or green. An amber tag not fixed within four weeks is treated as red.
- A useful report tells you what to fix first and why the damage keeps happening.
Most warehouse managers know their pallet racking needs inspecting under AS 4084. Fewer know what the inspector looks for or what to do with the report afterwards.
October is National Safe Work Month, and this year’s theme, Safe work is for life, is a good prompt to get clear on it.
What AS 4084 is, and why it matters in Victoria
AS 4084 is the Australian Standard for steel storage racking. The 2023 edition comes in two parts. Part 1 covers design. Part 2, AS 4084.2:2023, covers operation and maintenance, and that’s where inspections live.
The standard isn’t a law in its own right. But under Victoria’s Occupational Health and Safety Act 2004, employers must provide and maintain plant and a workplace that are safe, so far as reasonably practicable. WorkSafe Victoria’s pallet racking guidance says racking should be set up, operated and maintained according to the manufacturer’s instructions and AS 4084.2:2023, so an inspector or auditor will measure your racking against it.
There are two kinds of inspection
Informal checks are done by your own team, as often as the manufacturer or a competent person recommends. For many sites that means daily or weekly. Walk the aisles and look for impact damage, missing safety clips, sagging beams and loads that don’t sit properly.
Formal inspections are done by a competent person every 12 months, and you should receive a written report with observations and the corrective action needed. A competent person is someone with the training, qualifications or experience to do the job properly. Where racking is taller than 8 metres, the upper levels should be inspected from an elevating work platform, not eyeballed from the floor.
Your informal checks catch today’s problem. The formal inspection catches the ones your team has learned to walk past.
What the inspector actually looks at
- The loads. Are they the size, shape and weight the racking was designed for? Are pallets stable, secured and sitting properly on the beams, with the right clearances?
- The beams. Signs of overloading such as visible sag or connectors bent into a V, impact damage, cracked welds, missing safety clips, and beams that have been knocked out of place.
- Load signs. Are safe working load signs displayed, and do they still match how the racking is configured?
- Uprights and footplates. Dents, twists, splits and cracks, and whether any splices are in the right place.
- Plumb. Racking that leans, whether from installation, impact, overloading or the floor slab settling.
- Bracing and floor fixings. Bent braces, and anchors that are missing or damaged.
- Protection. Upright and end-of-run protectors where forklifts operate, and rear protection where people walk behind single-row racking.
A good inspector also asks what’s changed. New forklifts, different pallets, new products or moved beam levels can all change what your racking can safely hold, and any of them should be checked by a competent person.
Red, amber, green: what your report means
AS 4084.2:2023 sorts damage into three levels:
- Red: very serious. Offload the affected bays immediately and don’t use them again until they’re repaired.
- Amber: hazardous. Tag it, unload the affected locations and don’t reload them, and repair as soon as possible. If it isn’t fixed within four weeks, it’s treated as red.
- Green: acceptable. Tag it, record it and keep an eye on it. It gets reviewed at the next inspection.
We often see amber tags left open well past four weeks. Sometimes amber tags aren’t addressed until the next inspection, a full twelve months later.
What a good inspection gives you, beyond a report
A report is a list of problems. What you actually need is a plan: what’s urgent, what can wait until your next shutdown, who’s going to fix it, and why the damage is happening in the first place.
If the same upright keeps getting hit, replacing it again isn’t the answer. The fix might be protection, aisle width, the pick path or a refresher for operators. That’s the difference between an inspection that ticks a box and one that makes your warehouse safer next year than it is today.
When to book one
- It’s been more than 12 months since your last formal inspection, or you’re not sure when it was.
- You’ve changed forklifts, pallets, products or beam levels.
- There’s been an impact, even one that looked minor.
- You’ve taken over a site with existing racking.
- An insurer, auditor or WorkSafe inspector has asked to see your records.
Make October the month it’s sorted.
Our team inspects to AS 4084, talks you through what we find, and fixes it.
Over 35 years of satisfied customers.
Browse our latest projects
Didn’t answer your questions?
Epping, VIC 3076
Shepparton, VIC 3630





